Tuya TS0505B_1
Model | TS0505B_1 |
Vendor | Tuya |
Description | Zigbee RGB+CCT light |
Exposes | light (state, brightness, color_temp, color_xy), effect, do_not_disturb, color_power_on_behavior, linkquality |
Picture | |
White-label | Mercator Ikuü SMD4106W-RGB-ZB, Tuya A5C-21F7-01, Mercator Ikuü S9E27LED9W-RGB-Z, Aldi L122CB63H11A9.0W, Lidl 14153706L, Zemismart LXZB-ZB-09A, Feconn FE-GU10-5W, Nedis ZBLC1E14 |
Notes
Pairing
After powering the system the first time, the light is in pairing mode.
To reset a Tuya light: Firstly, make sure the device is powered off for more than 10 seconds before powering on the device. Then turn on and off three times (on-off-on-off-on) power of the device (2 to 4 seconds between each on and off). Wait a few moments until the lighting starts blinking rAPIDly. The device is ready for pairing
Options
How to use device type specific configuration
transition
: Controls the transition time (in seconds) of on/off, brightness, color temperature (if applicable) and color (if applicable) changes. Defaults to0
(no transition). The value must be a number with a minimum value of0
color_sync
: When enabled colors will be synced, e.g. if the light supports both color x/y and color temperature a conversion from color x/y to color temperature will be done when setting the x/y color (default true). The value must betrue
orfalse
state_action
: State actions will also be published as 'action' when true (default false). The value must betrue
orfalse
Exposes
Light
This light supports the following features: state
, brightness
, color_temp
, color_xy
.
state
: To control the state publish a message to topiczigbee2mqtt/FRIENDLY_NAME/set
with payload{"state": "ON"}
,{"state": "OFF"}
or{"state": "TOGGLE"}
. To read the state send a message tozigbee2mqtt/FRIENDLY_NAME/get
with payload{"state": ""}
.brightness
: To control the brightness publish a message to topiczigbee2mqtt/FRIENDLY_NAME/set
with payload{"brightness": VALUE}
whereVALUE
is a number between0
and254
. To read the brightness send a message tozigbee2mqtt/FRIENDLY_NAME/get
with payload{"brightness": ""}
.color_temp
: To control the color temperature (in reciprocal megakelvin a.k.a. mired scale) publish a message to topiczigbee2mqtt/FRIENDLY_NAME/set
with payload{"color_temp": VALUE}
whereVALUE
is a number between153
and500
, the higher the warmer the color. To read the color temperature send a message tozigbee2mqtt/FRIENDLY_NAME/get
with payload{"color_temp": ""}
. Besides the numeric values the following values are accepted:coolest
,cool
,neutral
,warm
,warmest
.color_xy
: To control the XY color (CIE 1931 color space) publish a message to topiczigbee2mqtt/FRIENDLY_NAME/set
with payload{"color": {"x": X_VALUE, "y": Y_VALUE}}
(e.g.{"color":{"x":0.123,"y":0.123}}
). To read the XY color send a message tozigbee2mqtt/FRIENDLY_NAME/get
with payload{"color":{"x":"","y":""}}
. Alternatively it is possible to set the XY color via RGB:{"color": {"r": R, "g": G, "b": B}}
e.g.{"color":{"r":46,"g":102,"b":150}}
{"color": {"rgb": "R,G,B"}}
e.g.{"color":{"rgb":"46,102,150"}}
{"color": {"hex": HEX}}
e.g.{"color":{"hex":"#547CFF"}}
On with timed off
When setting the state to ON, it might be possible to specify an automatic shutoff after a certain amount of time. To do this add an additional property on_time
to the payload which is the time in seconds the state should remain on. Additionally an off_wait_time
property can be added to the payload to specify the cooldown time in seconds when the light will not answer to other on with timed off commands. Support depends on the light firmware. Some devices might require both on_time
and off_wait_time
to work Examples : {"state" : "ON", "on_time": 300}
, {"state" : "ON", "on_time": 300, "off_wait_time": 120}
.
Transition
For all of the above mentioned features it is possible to do a transition of the value over time. To do this add an additional property transition
to the payload which is the transition time in seconds. Examples: {"brightness":156,"transition":3}
, {"color_temp":241,"transition":1}
.
Moving/stepping
Instead of setting a value (e.g. brightness) directly it is also possible to:
- move: this will automatically move the value over time, to stop send value
stop
or0
. - step: this will increment/decrement the current value by the given one.
The direction of move and step can be either up or down, provide a negative value to move/step down, a positive value to move/step up. To do this send a payload like below to zigbee2mqtt/FRIENDLY_NAME/set
NOTE: brightness move/step will stop at the minimum brightness and won't turn on the light when it's off. In this case use brightness_move_onoff
/brightness_step_onoff
{
"brightness_move": -40, // Starts moving brightness down at 40 units per second
"brightness_move": 0, // Stop moving brightness
"brightness_step": 40 // Increases brightness by 40
"color_temp_move": 60, // Starts moving color temperature up at 60 units per second
"color_temp_move": "stop", // Stop moving color temperature
"color_temp_step": 99, // Increase color temperature by 99
}
Effect (enum)
Triggers an effect on the light (e.g. make light blink for a few seconds). Value will not be published in the state. It's not possible to read (/get
) this value. To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"effect": NEW_VALUE}
. The possible values are: blink
, breathe
, okay
, channel_change
, finish_effect
, stop_effect
, colorloop
, stop_colorloop
.
Do not disturb (binary)
Do not disturb mode, when enabled this function will keep the light OFF after a power outage. Value can be found in the published state on the do_not_disturb
property. It's not possible to read (/get
) this value. To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"do_not_disturb": NEW_VALUE}
. If value equals true
do not disturb is ON, if false
OFF.
Color power on behavior (enum)
Power on behavior state. Value can be found in the published state on the color_power_on_behavior
property. It's not possible to read (/get
) this value. To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"color_power_on_behavior": NEW_VALUE}
. The possible values are: initial
, previous
, customized
.
Linkquality (numeric)
Link quality (signal strength). Value can be found in the published state on the linkquality
property. It's not possible to read (/get
) or write (/set
) this value. The minimal value is 0
and the maximum value is 255
. The unit of this value is lqi
.